www.vishay.com for technical questions, contact: eurotant@vishay.com document number: 42073 1 revision: 11-may-07 cts1, cts13, 749dx vishay sprague hermetically sealed, axial-lead, to cecc specifications features terminations: tin/lead (snpb), 100 % tin (rohs compliant) ? hermetically sealed metal case with plastic film insulation ? extended capacitance range (type 749dx) ? high operational stability with both time and temperature ? low leakage current ? low dissipation factor applications performance and reliability has been proven in a wide range of applications such as: filter ing, by-pass, coupling, energy storage, timing circuits. a v aila b le rohs* compliant performance characteristics operating temperature: - 55 c to + 85 c (types cts13) - 55 c to + 125 c (types cts1, 749dx) specifications cecc bs 30201-001 749dx 9073-n001 749dx 30201-002 cts1 30201-005 cts13 30201-011/012 749dx iecq 30201-029 749dx ordering information cts13 105 x0 040 a 2 p e3 type capacitance capacitance to l e r a n c e dc voltage rating at + 85 c case code style number packaging rohs compliant identifies the basic capacitor design cts1 = cecc 30201-002 cts13 = cecc 30201-005 749dx = cecc 30201-001/011/012/029 expressed in picofarads. first two digits are significant. third digit is the number of zeros following. x0 = 20 % x9 = 10 % x5 = 5 % (special order) expressed in volts. where necessary, zeros precede the voltage rating to complete the 3 digit block 6r3 = 6.3 volts see ta b l e ratings and case codes. 0 = bare case 2 = plastic-film insulation see taping and packaging e3 = 100 % tin termination (rohs compliant) blank = snpb termination note * pb containing terminations are not rohs compliant, exemptions may apply dimensions in millimeters case code bs d max. nf d max. l max. + 10 % ? d - 0.05 a 3.6 3.8 10.2 0.5 b 4.9 5.1 15.0 0.5 c 7.5 7.7 20.5 0.6 d 9.1 9.3 24.0 0.6 30 min.* d max. l max. *23 mm max. for taped capacitors 30 min. ? d
document number: 42073 for technical questions, contact: eurotant@vishay.com www.vishay.com revision: 11-may-07 2 cts1, cts13, 749dx hermetically sealed, axial-lead, to cecc specifications vishay sprague type cts1: standard ratings and case codes c r f rated voltage u r (+ 85 c) 6.3 v 10 v 16 v 25 v 40 v 50 v 53 v 80 v 100 v 125 v category voltage u c (+ 125 c) 4 v 6.3 v 10 v 13 v 25 v 33 v 40 v 50 v 67 v 82 v 0.10 aaaa 0.12 aaaa 0.15 aaaa 0.18 aaaa 0.22 aaaa 0.27 aaaaa 0.33 aaaaa 0.39 aaaab 0.47 aaaaab 0.56 aaaaab 0.68 aaaabb 0.82 aabbbb 1.0 aabbbb 1.2 abbbbb 1.5 abbbbbb 1.8 a bbbbbb 2.2 a bbbbbb 2.7 a bbbbb 3.3 a bbbbc 3.9 a bbbbc 4.7 a bbccc 5.6 a b c c c c 6.8 a bcccc 8.2 b c c c c 10 bcccc 12 b c c d d 15 b c c d d 18 b c c d 22 b c d 27 b c d 33 b c d 39 b c d 47 b c d 56 b c d 68 c d 82 c d 100 c d 120 c d 150 c d 180 d 220 d 270 d 330 d preferred ratings are in bold characters. non-preferred ratings are av ailable only with a capacitance tolerance of 10 % or 5 % (special order).
cts1, cts13, 749dx vishay sprague hermetically sealed, axial-lead, to cecc specifications www.vishay.com for technical questions, contact: eurotant@vishay.com document number: 42073 3 revision: 11-may-07 type cts13: standard ratings and case codes c r f rated voltage u r (+ 85 c ) 6.3 v 10 v 16 v 20 v 25v 40 v 50 v 63 v 0.10 a a a 0.12 a a a 0.15 a a a 0.18 a a a 0.22 a a a 0.27 a a a 0.33 a a a 0.39 a a a 0.47 a a a 0.56 a a a 0.68 a a a 0.82 a a b 1.0 a a b 1.2 a a b b 1.5 a b b b 1.8 a b b b 2.2 a b b b 2.7 a b b b 3.3 a b b b 3.9 a b b b 4.7 a b b c 5.6 a b c c 6.8 a b c c 8.2 b c c c 10 b c c c 12 b c c d 15 b c c d 18 b c c d 22 b c d 27 b c d 33 b c d 39 b c d 47 b c d 56 b c d 68 c d 82 c d 100 c d 120 c d 150 c d 180 d 220 d 270 d 330 d preferred ratings are in bold c haracters. non-preferred ratings are available only with a capacit ance tolerance of 10 % or 5 % (special order).
document number: 42073 for technical questions, contact: eurotant@vishay.com www.vishay.com revision: 11-may-07 4 cts1, cts13, 749dx hermetically sealed, axial-lead, to cecc specifications vishay sprague type 794dx: standard ratings and case codes c r f rated voltage u r ( + 85 c ) 6.3 v 10 v 16 v 20 v 25 v 35 v 40 v 50 v 63 v category voltage u c ( + 125 c ) 4 v 6.3 v 10 v 13 v 16 v 23 v 25 v 33 v 40 v 0.068 a 0.085 a 0.10 a a a 0.12 a a a 0.15 a a a 0.18 a a a 0.22 a a a 0.27 a a a 0.33 a a a 0.39 a a a 0.47 a a a 0.56 a a a 0.68 a a a 0.82 a a a b 1.0 a a a b 1.2 a b b b b 1.5 a b b b b 1.8 a b b b b 2.2 a b b b b 2.7 a b b b b 3.3 a b b b b 3.9 a b b b b 4.7 a b b * c 5.6 a b b c c 6.8 a * * c c 8.2 b c c c c 10 b c c c c 12 b c c c d 15 b c c c d 18 b c c c d 22 b c c d 27 b c d d 33 b c d d 39 b c d d 47 b c d 56 b c d * 68 c d 82 c d 100 c d 120 c d 150 c d 180 c d 220 d 270 d 330 d *see extended range page
cts1, cts13, 749dx vishay sprague hermetically sealed, axial-lead, to cecc specifications www.vishay.com for technical questions, contact: eurotant@vishay.com document number: 42073 5 revision: 11-may-07 type 749dx: extended ratings and case codes c r f rated voltage u r ( + 85 c ) 6.3 v 10 v 16 v 20 v 25 v 35 v 50 v category voltage u c ( + 125 c ) 4 v 6.3 v 10 v 13 v 16 v 23 v 32 v 1.2 a a 1.5 a a 1.8 a 2.2 a 2.7 a 3.3 a 3.9 a a 4.7 a a b 5.6 a b 6.8 a b 8.2 a b 10 a 12 a b 15 a b 18 b b 22 b c 27 b c d 33 b c d 39 b c d 47 b c 56 b c d 68 b c d 82 b d 100 b c c d 120 b c c d 150 c d 180 c d 220 c d d 270 c d 330 c d d 390 c d 470 c d 560 d 680 d 820 d 1000 d preferred ratings are in bold c haracters. non-preferred ratings are available only with a capacitance tolerance of 10 % or 5 % (special order).
document number: 42073 for technical questions, contact: eurotant@vishay.com www.vishay.com revision: 11-may-07 6 cts1, cts13, 749dx hermetically se aled, axial-lead, to cecc specifications vishay sprague typical curves ripple voltage at + 25 c 100 10 1 0.1 1k 10k 100k 10 100 1m frequency in hertz volts rms 50 0.5 30 2 40 20 5 4 3 0.4 0.2 0.3 case b capacitors 35v & 40v 20v & 25v 6.3v 16v 10v 50v & 63v 80v 100v & 125v 100 10 1 0.1 1k 10k 100k 10 100 1m frequency in hertz volts rms 50 0.5 30 2 40 20 5 4 3 0.4 0.2 0.3 case d capacitors 35v & 40v 6.3v 16v 10v 100v & 125v 20v & 25v 50v & 63v 80v 100 10 1 0.1 1k 10k 100k 10 100 1m frequency in hertz volts rms 50 0.5 30 2 40 20 5 4 3 0.4 0.2 0.3 case a capacitors 35v & 40v 20v & 25v 6.3v 16v 10v 50v & 63v 80v 100v & 125v 100 10 1 0.1 1k 10k 100k 10 100 1m frequency in hertz volts rms 50 0.5 30 2 40 20 5 4 3 0.4 0.2 0.3 case c capacitors 35v & 40v 20v & 25v 6.3v 16v 10v 50v & 63v 80v 100v & 125v
cts1, cts13, 749dx vishay sprague hermetically sealed, axial-lead, to cecc specifications www.vishay.com for technical questions, contact: eurotant@vishay.com document number: 42073 7 revision: 11-may-07 performance characteristics 1. operating temperature: - 55 c to + 85 c with rated dc voltage ur applied, + 85 c to + 125 c with linear voltage derating to category voltage uc (only for types cts1, 749dx). 2. capacitance and tolerance: capacitance measured at 100 hz and + 25 c shall be within the specified tolerance limits of the nominal rating. capacitance measurement shall be made by means of a polarized capacitance bridge. the polarizing voltage shall be of 2.2 volts. the maximum voltage applied during measurements shall be 1.0 volt rms at 100 hz and + 25 c. 3. reverse voltage: these capacitors are capable of withstanding peak voltage in the reverse direction equal to: 15 % of the rated dc voltage at + 25 c, 5 % of the rated dc voltage at + 85 c. 4. surge voltage: table 1 capacitors shall withstand the surge voltage applied in series with a 1000 ohm resistor, at the rate of one halfminute on, five and a half-minute off, for 1000 successive test cycles at + 85 c or at + 125 c. after test, dissipation factor and leakage current shall meet the initial requirements at + 25 c (see below), capacitance change shall not exceed 10 % of initial value at + 25 c. 5. leakage current: rated voltage ur shall be applied to capacitors during five minutes with a resistor of 1000 ohm in series with each capacitor, before making dc leakage current measurements. the leakage current shall not exceed the following limits: table 2 6. dissipation factor: the dissipation factor, when measured at 100 hz, shall not exceed the values below: table 3 7. stability at low and high temperature: capacitance change with temperature shall not exceed the limits of the following table, leakage current and dissipation factor shall be within the lim its specified in tables 2 and 3. table 4 8. impedance: the impedance measured at 100 khz and 25 c shall not exceed the following values: table 5 9. life test: after 2000 hours at + 85 c with rated dc voltage applied, or after 2000 hours at + 125 c with category dc voltage applied (for types cts1, 749dx only) capacitors shall meet the requirements in table 6. table 6 product type surge voltage at + 85 c surge voltage at + 125 c cts13 1.30 u r - 749dx/cts1 1.30 u r 1.30 u c temperature cts1/cts13/749dx + 25 c 0.01 c r x u r or 1 a whichever is greater + 85 c 0.1 c r x u r or 10 a whichever is greater +125 c 0.125 c r x u r or 12.5 a whichever is greater temp. cts1/cts13 749dx c r u r 1900 c r u r > 1900 c r 100 c r > 100 - 55 c 9 % 11 % 8 % 10 % + 25 c 6 % 8 % 6 % 8 % + 85 c 9 % 11 % - - + 125 c* 12 % 14 % 10 % 11 % *not applicable for cts13 temperature cts1/cts13/749dx - 55 c - 10 % + 85 c + 12 % + 125 c * + 15 % *not applicable for cts13 case code z ( )* a10 b5 c2 d1 * not applicable for c r 0.68 f product type capacitance change dissipation factor dc leakage current cts1 cts13 749dx within 10 % of initial value at + 25 c within initial requirement at + 25 c within 125 % of initial requirements at + 25 c
document number: 42073 for technical questions, contact: eurotant@vishay.com www.vishay.com revision: 11-may-07 8 cts1, cts13, 749dx hermetically se aled, axial-lead, to cecc specifications vishay sprague performance characteristics (continued) 10. humidity test: after 56 days (1350 hours) at + 40 c, 90 to 95 % of relative humidity (per iec 68-2-3) with no voltage applied, capacitors shall meet the requirements in table 7 below. table 7 table 8 typical values of charge-discharge current (per above test conditions) . 12. insulation test: for capacitors with insulating sleeves, a dc voltage of 100 volts shall be applied for one minute between the case of the capacitor and a metal ?v? block in intimate contact with the insulating sleeve. the insulating resistance measured in these conditions shall be at least 100 megohms. 13. lead pull test: leads shall withstand the following test (iec 68 - 2 - 2): ? tensile stress of 5n (cases a and b) or 10n (cases c and d) for 10 seconds in any direction ? one bend in each direction ? two consecutive rotations of 180 guide to application 1. a-c ripple current: the maximum allowable ripple current shall be determined from the formula: where, p = power dissipation in watts at + 25 c as given below resr = the capacitor equivalent series resistance at the specified frequency. 2. a-c ripple voltage: the maximum allowable ripple voltage shall be determined from the formula: where, z = the capacitor impedance at the specified frequency. the calculations are summarized on the graphs page 7 giving the maximum available ripple voltage as a function of frequency. however, the sum of the peak ac voltage plus the dc voltage shall not exceed the rated dc voltage at + 85 c of the capacitor. th e sum of the negative peak ac voltage plus the dc voltage shall not allow a voltage reversal exceeding 15 % of the rated dc voltage. 3. ac ripple current or voltage derating factor: if these capacitors are to be operated at temperatures above + 25 c, the permissible rms ripple current or voltage shall be calculated using the derating factors in the table below: 4. power dissipation: power dissipation will be affected by the heat sinking capability of the mounting surface. non-sinusoidial ripple current may produce heating effects which differ from those shown in the following table. it is important that the equivalent irms value be established when calculating permissible operating levels. capacitance change within 3 % of initial value dc leakage current within initial requirement at + 25 c -table 2 dissipation factor within initial requirement at + 25 c - table 3 capacitance change within 5 % of initial value at + 25 c dc leakage current within initial requirement at + 25 c - table 2 dissipation factor within initial requirement at + 25 c - table 3 rated voltage u r (v) charge-discharge current (a) 6.3 13 10 20 16 32 25 50 40 80 50 100 63 126 temperature derating factor + 25 c 1.0 + 55 c 0.8 + 85 c 0.6 + 125 c 0.4 case code power dissipation at + 25 c (watts) a 0.115 b 0.145 c 0.185 d 0.225 i rms p r esr --------------- - = v rms p r esr ----------------- z =
cts1, cts13, 749dx vishay sprague hermetically sealed, axial-lead, to cecc specifications www.vishay.com for technical questions, contact: eurotant@vishay.com document number: 42073 9 revision: 11-may-07 marking capacitors shall be marked with sprague and/or the registered tr ademark 2 at vendor?s option ; the type number ; rated capacitance and tolerance (with a letter code, if different from 20 %, k = 10 % ; j = 5 %) ; rated dc voltage at + 85 c and the date code of manufacture. capacitors shall be marked on one end with a ?plus? sign (+) to identify the positive terminal. tape and reel packing dimensions in millimeters case size reel and ammo s reel pack ammo pack bulk option p option r qty per reel option g qty per box qty per pack b c max b c max b c max a 5.0 0.3 63 2 78 53 2 68 1000 53 2 68 500 100 b 5.0 0.3 63 2 78 53 2 68 1000 53 2 68 500 75 c 10.0 0.3 63 2 78 63 2 78 500 53 2 68 250 50 d 10.0 0.3 63 2 78 63 2 78 500 53 2 68 250 25 pakkaging code pr gb 0.2 0.3 l1 l2 b c s 1.5 max. meets iec 286-1 l1 - l2 = 1.5 mm max s = component spacing (cumulativ e tolerance on 20 units = 4 mm) b = tape spacing c = overall length
legal disclaimer notice vishay document number: 91000 www.vishay.com revision: 08-apr-05 1 notice specifications of the products displayed herein are subjec t to change without notice. vishay intertechnology, inc., or anyone on its behalf, assume s no responsibility or liability fo r any errors or inaccuracies. information contained herein is intended to provide a product description only. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in vishay's terms and conditions of sale for such products, vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and /or use of vishay products including liab ility or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyrigh t, or other intellectual property right. the products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify vishay for any damages resulting from such improper use or sale.
|
